mirror of
https://github.com/riegera2412/UVtools.git
synced 2026-07-09 18:12:32 +02:00
master
14 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
 Tiago Conceição
|
9f7722d369 |
v3.7.0
- **File formats:** - (Add) `TransitionLayerCount` modifier to: Chitubox Zip, CWS, JXS, OSLA, PW*, UVJ, ZCodex, ZCode - (Add) Utility methods for transition layers calculation/parse - (Improvement) Calculate and set `TransitionLayerCount` property in file decode based on layer exposure time configuration - **GCode:** - (Improvement) GCode: Able to parse layer image file with appended numbers on the filename (Afecting CWS) (#577) - (Fix) Bad parsing of the file when it comes from Lychee or NovaMaker slicer (Afecting CWS) - (Fix) Incorrect parse of "Wait time before cure" from layers when printer require wait sync moves (Afecting CWS) - **Tools:** - (Add) External tests: The Complete Resin 3D Printing Settings Guide for Beginners - (Add) External tests: 9 settings for faster printing - (Improvement) Fade exposure time: Set `TransitionLayerCount` property with the affected layer count - **Suggestions:** - (Add) Transition layers: If you are printing flat on the build plate your model will print better when using a smooth transition exposure time instead of a harsh variation, resulting in reduced layer line effect and avoid possible problems due the large exposure difference. This is not so important when your model print raised under a raft/supports unaffected by the bottom exposure, in that case, it's fine to ignore this. - (Add) Model position: Printing on a corner will reduce the FEP stretch forces when detaching from the model during a lift sequence, benefits are: Reduced lift height and faster printing, less stretch, less FEP marks, better FEP lifespan, easier to peel, less prone to failure and use the screen pixels more evenly. If the model is too large to fit within the margin(s) on the screen, it will attempt to center it on that same axis to avoid touching on screen edge(s) and to give a sane margin from it. - **Status bar:** - (Add) Transition layers: 0/-0.00s - (Improvement) Change "Layer Height: 0.000mm" to "Layers: count @ 0.000mm" - (Improvement) Change "Bottom layers: 0" to "Bottom layers: 0/0.000mm" - (Change) Show user informative message about CTB Encrypted file format once per ten file loads - (Upgrade) .NET from 6.0.9 to 6.0.10 - (Fix) Windows MSI installation not upgrading well when downgrade libraries |
||
|
Tiago Conceição
|
f7d989d29f |
v3.6.1
- (Fix) GCode: Improve the regex for parsing layer index from comments, also fixes chitubox zip format layer parsing - (Fix) MacOS: Auto updater was not copying the files to the right location, leading to not upgrade the program. However this version still need to update manually |
||
|
Tiago Conceição
|
57f077f444 |
v3.6.0
- **File formats:** - (Add) OSF (Vlare Open File Format) - (Fix) CTB Encrypted: Bottom Retract Height for TSMC was constraining incorrectly with the normal total retract height - (Fix) CWS: Only issue `;<Slice>` command when the exposure is about to happen (#514) - **GCode:** - (Add) Command `CommandWaitSyncDelay` for movement wait sync delay instead of depending on G4 wait command - (Fix) Wrong parsing and set of wait times when using a wait after lift / wait before retract - (Improvement) Auto update: Make sure the download url exists before attempt the download, if not, instead it will prompt for manual download and update - (Improvement) MacOS: Remove `com.apple.quarantine` flag from the auto downloaded files - (Upgrade) .NET from 6.0.7 to 6.0.8 - (Upgrade) AvaloniaUI from 0.10.17 to 0.10.18 |
||
|
Tiago Conceição
|
57b8a9dc84 |
v3.2.0
- **Core:**
- (Add) Machine presets and able to load machine collection from PrusaSlicer
- (Improvement) Core: Reference EmguCV runtimes into core instead of the UI project
- **File formats:**
- **CXDLP:**
- (Add) Detection support for Halot One Pro
- (Add) Detection support for Halot One Plus
- (Add) Detection support for Halot Sky Plus
- (Add) Detection support for Halot Lite
- (Improvement) Better handling and detection of printer model when converting
- (Improvement) Discovered more fields meanings on format
- (Fix) Exposure time in format is `round(time * 10, 1)`
- (Fix) Speeds in format are in mm/s, was using mm/min before
- (Add) JXS format for Uniformation GKone [Zip+GCode]
- (Improvement) Saving and converting files now handle the file backup on Core instead on the UI, which prevents scripts and other projects lose the original file in case of error while saving
- (Fix) After load files they was flagged as requiring a full encode, preventing fast save a fresh file
- **UVtoolsCmd:**
- Bring back the commandline project
- Consult README to see the available commands and syntax
- Old terminal commands on UVtools still works for now, but consider switch to UVtoolsCmd or redirect the command using `UVtools --cmd "commands"`
- **Tools:**
- **Change print resolution:**
- (Add) Allow to change the display size to match the new printer
- (Add) Machine presets to help set both resolution and display size to a correct printer and auto set fix pixel ratio
- (Improvement) Real pixel pitch fixer due new display size information, this allow full transfers between different printers "without" invalidating the model size
- (Improvement) Better arrangement of the layout
- (Add) Infill: Option "Reinforce infill if possible", it was always on before, now default is off and configurable
- (Improvement) Always allow to export settings from tools
- **GCode:**
- (Improvement) After print the last layer, do one lift with the same layer settings before attempt a fast move to top
- (Improvement) Use the highest defined speed to send the build plate to top after finish print
- (Improvement) Append a wait sync command in the end of gcode if needed
- (Fix) When lift without a retract it still output the motor sync delay for the retract time and the wait time after retract
- **PrusaSlicer:**
- (Add) Printer: Creality Halot One Pro CL-70
- (Add) Printer: Creality Halot One Plus CL-79
- (Add) Printer: Creality Halot Sky Plus CL-92
- (Add) Printer: Creality Halot Lite CL-89L
- (Add) Printer: Creality Halot Lite CL-89L
- (Add) Printer: Creality CT133 Pro
- (Add) Printer: Creality CT-005 Pro
- (Add) Printer: Uniformation GKone
- (Add) Printer: FlashForge Foto 8.9S
- (Add) Printer: Elegoo Mars 2
- (Improvement) Rename all Creality printers
- (Fix) Creality model in print notes
|
||
|
Tiago Conceição
|
4600e81b08 |
v3.0.0
- **(Add) Suggestions:**
- A new module that detect bad or parameters out of a defined range and suggest a change on the file, those can be auto applied if configured to do so
- **Avaliable suggestions:**
- **Bottom layer count:** Bottom layers should be kept to a minimum, usually from 2 to 3, it function is to provide a good adhesion to the first layer on the build plate, using a high count have disadvantages.
- **Wait time before cure:** Rest some time before cure the layer is crucial to let the resin settle after the lift sequence and allow some time for the arm settle at the correct Z position as the resin will offer some resistance and push the structure.
This lead to better quality with more successful prints, less lamination problems, better first layers with more success of stick to the build plate and less elephant foot effect.
- **Wait time after cure:** Rest some time after cure the layer and before the lift sequence can be important to allow the layer to cooldown a bit and detach better from the FEP.
- **Layer height:** Using the right layer height is important to get successful prints:
Thin layers may cause problems on adhesion, lamination, will print much slower and have no real visual benefits.
Thick layers may not fully cure no matter the exposure time you use, causing lamination and other hazards. Read your resin dtasheet to know the limits.
Using layer height with too many decimal digits may produce a wrong positioning due stepper step loss and/or Z axis quality.
- **Core:**
- Convert the project to Nullable aware and "null-safe"
- **File Formats:**
- (Add) `Volume` property to get the total model volume
- (Add) `SanitizeLayers` method to reassign indexes and force attribute parent file
- (Improvement) Merge `LayerManager` into `FileFormat` and cleanup: This affects the whole project and external scripts.
If using scripts please update them, search for `.LayerManager.` and replace by `.`
- (Change) Chitubox encrypted format can now be saved as normal
- (Fix) Converted files layers was pointing to the source file and related to it
- **Layers:**
- (Add) Methods: `ResetParameters`, `CopyParametersTo`, `CopyExposureTo`, `CopyWaitTimesTo`
- (Improvement) `IsBottomLayer` property will also return true when the index is inside bottom layer count
- **Scripting:**
- (Add) Configuration variable: `MinimumVersionToRun` - Sets the minimum version able to run the script
- (Improvement) Allow run scripts written in C# 10 with the new namespace; style as well as nullables methods
- (Improvement) Convert scripts to use Nullable code
- **UI:**
- (Add) Fluent Dark theme
- (Add) Default Light theme
- (Add) Default Dark theme
- (Change) Use fontawesome and material design to render the icons instead of static png images
- (Change) Some icons
- (Change) Move log tab to clipboard tab
- (Change) Tooltip overlay default color
- (Improvement) Windows position for tool windows, sometimes framework can return negative values affecting positions, now limits to 0 (#387)
- (Fix) Center image icon for layer action button
- (Fix) Center image icon for save layer image button
- **Tools:**
- (Add) Layer re-height: Offset mode, change layers position by a defined offset (#423)
- (Improvement) Rotate: Unable to use an angle of 0
- (Improvement) Remove layers: Will not recalcualte and reset properties of layers anymore, allowing removing layers on dynamic layer height models and others
- (Improvement) Clone layers: Will not recalcualte and reset properties of layers anymore, allowing cloning layers on dynamic layer height models and others
- (Fix) Exposure time finder: Very small printers may not print the stock object as it is configured, lead to a unknown error while generating the test. It will now show a better error message and advice a solution (#426)
- **Terminal:**
- (Add) More default namespaces
- (Improvement) Set a MinHeight for the rows to prevent spliter from eat the elements
- (Change) Set working space to the MainWindow instead of TerminalWindow
- **(Upgrade) .NET from 5.0.14 to 6.0.3**
- This brings big performance improvements, better JIT, faster I/O operations and others
- Read more: https://devblogs.microsoft.com/dotnet/performance-improvements-in-net-6
- Due this macOS requirement starts at 10.15 (Catalina)
- Read more: https://github.com/dotnet/core/blob/main/release-notes/6.0/supported-os.md
- (Add) Native support for MacOS ARM64 architecture (Mac M1 and upcomming Mac's) (#187)
- (Exchange) Dependency Newtonsoft Json by System.Text.Json to parse the json documents
- (Remove) "Automations - Light-off delay" in favor of new suggestion "wait time before cure" module
- (Fix) File - Send to: Winrar or 7zip have a wrong extension on the list (uvt) when should be (uvj)
- (Upgrade) AvaloniaUI from 0.10.12 to 0.10.13
|
||
|
Tiago Conceição
|
069c521d72 |
v2.29.0
- **File formats:**
- (Add) Transition layer count to the supported files and auto compute transition time on corresponding layers in software mode
- (Add) `HaveTransitionLayers`, `TransitionLayersType`, `BottomLayers`, `NormalLayers`, `TransitionLayers`, `TsmcLayers` properties
- (Add) Layer: `IsTransitionLayer` property
- (Add) SL1: Keyword `TransitionLayerCount_xxx` - Sets the number of transition layers
- (Improvement) CTB, PHZ, FDG: Implement the `ModifiedTimestampMinutes` field, it was the MysteriousId before as an unknown field
- (Fix) CWS: Open in partial mode will cause an exception and prevent file from load
- **CCode:**
- (Add) Allow inverse lifts to work as an retract
- (Fix) Parsing of WaitTimeAfterLift was incorrect when lacking a lift sequence
- (Fix) Layers lacking an exposure time was defaulting to global time, now defaults to 0
- (Fix) Layers without a LED ON (M106) was setting `LightPWM` to the max value (255), now defaults to 0
- **Tools:**
- **Timelapse:**
- (Add) Information: Raise Layer count equivalence
- (Add) Information: Additional lifts to be generated
- (Add) Option: Ensure the last layer - If enabled, it will generate an obligatory layer to cover the last layer
- (Improvement) Optimize lift for virtual layer mode, allowing set a slow and fast lift / retract by using another virtual layyer to emulate a lift
- (Improvement) Allow to define slow and fast speed for virtual layer mode even if TSMC isn't supported
- (Add) Fade exposure time: Setting 'Disable firmware transition layers' - Attempt to disable firmware strict transition layers in favor of this tool
- (Add) Calibration tests: Attempt to auto disable the firmware transifiton layers
- (Change) Edit print parameters: Allow set `BottomLiftHeight` and `LiftHeight` to 0mm
- **UI:**
- (Improvement) Disallow drop files into UI when is processing data / disabled and prevent crashing from that action
- (Improvement) Information tab visibility and MinHeight for data grids
- (Improvement) Hide/show GCode tab when necessary (dependent on file format)
- (Improvement) The 'save as' will show the new file into 'Open recent' files
- **PrusaSlicer printers:**
- (Add) Elegoo Jupiter
- (Add) EPAX X1 4KS
- (Add) EPAX DX1 Pro
- (Add) EPAX DX10 Pro 5K
- (Add) EPAX DX10 Pro 8K
- (Add) EPAX E10 8K
- (Add) EPAX X133 6K
|
||
|
Tiago Conceição
|
554794d0d8 |
v2.28.0
- **Core:**
- (Add) Utilities methods (`MinimumSpeed`, `MaximumSpeed`, `CreateMat`, `CreateMatWithDummyPixel`, `FileFormat.CopyParameters`)
- (Improvement) Issues - Print Height: Group all layers outside the valid print height
- **FileFormats:**
- (Add) Generic / Phrozen ZIP format
- (Add) Information/modifier to file formats to tell whatever is possible to use custom PositionZ per layer
- (Add) Safe checks in order to run some tools, related to the previous "PositionZ" point
- (Improvement) if blank, allow the previous layer to have a higher Z position than the successor layer
- (Improvement) SL1: Implement the missing keys from new features of PrusaSlicer 2.4.0
- (Fix) Calling a partial save action without a progress instance would cause a crash
- (Fix) GCode: Unable to parse the "Wait time after lift" when a second lift (TSMC) was present, leading to a sum on "Wait time before cure"
- **Tools:**
- (Add) Timelapse: Raise the build platform to a set position every odd-even height to be able to take a photo and create a time-lapse video of the print
- (Add) Scripting: ScriptToggleSwitchInput
- **Raise on print finish:**
- (Add) Reapply check and prevent run the tool in that case
- (Fix) It was incorrectly marked to be able to run in partial mode
- (Fix) The dummy pixel was beeing set to a wrong location
- **Layers:**:
- (Change) When set Wait times to a negative value, it will set the global wait time value accordingly
- (Change) Allow ExposureTime to be 0
- **Commandline arguments**
- (Add) --run-operation \<input_file\> \<operation_file.uvtop\>
- (Add) --run-script \<input_file\> \<script_file.cs\>
- (Add) --copy-parameters \<from_file\> \<to_file\>
- **UI:**
- (Add) When open a file with missing crucial information, prompt the user to fill in that information (Optional)
- (Add) Warn user about misfunction when open a file with invalid layer height of 0mm
- (Improvement) Layer information: Only show the "Exposure time" when its availiable on the file format
- (Improvement) When a file is about to get auto-converted once loaded and the output file already exists, prompt user for overwrite action
- (Improvement) Set default culture info at top most of the program to avoid strange problems with commandline arguments
- (Upgrade) .NET from 5.0.13 to 5.0.14
- (Downgrade) OpenCV from 4.5.5 to 4.5.4 due the crash while detecting islands (Linux and MacOS) (#411, #415, #416)
|
||
|
Tiago Conceição
|
1e787ba11b |
Nuke issue system
- Issues: - (Add) Suction cups: Add a auto repair feature for this issues by drill a vertical vent hole (#296) - (Add) Layer issue track bar: Colorize the issue tracker map with it own colors (Configurable) - (Add) Allow to group issues by type and/or layer - (Improvement) Order issues by area in descending order - (Improvement) Always bring the selected issue into view on the list - (Fix) When manually removing a issue from the list, it will no longer reselect other and make the user lost track of the remove issue - (Fix) Allow to ignore all issue type - (Fix) Material ml calculation was calculating a bad value for PhotonWorkshop files |
||
|
Tiago Conceição
|
72d8636d4a |
v2.20.2
- **(Fix) Layers:** - Round properties before comparing to avoid the precision error - Prevent 'Wait time' properties from having negative values - The `RetractSpeed` or `RetractSpeed2` property wasn't setting the bottom speed for bottom layers, instead the normal retract speed was always used - Set the `RetractHeight2` or `RetractSpeed2` property was not notifing the timer to update the print time no - Propagate global settings to layers now identfies the bottom layers per height instead of layer index - (Add) UVJ: Support TSMC for the file format - (Fix) UVJ: Soft save was not updating the layer settings - (Fix) CTB: TSMC not working properly due incorrect layer `LiftHeight` value calculation |
||
|
Tiago Conceição
|
c670551140 |
v2.19.2
- **File Formats:** - (Fix) Setting a global property that haven't a bottom counter-part will notify and set that value to bottom layers too - (Fix) TSMC: Update lift or retract height for the first time will set the `RetractHeight2` property to 0 - (Fix) TSMC: `RetractHeight` is the first fast sequence paired with `RetractSpeed` - (Fix) TSMC: `RetractHeight2` paired with `RetractSpeed2` is performed after the `RetractHeight` and controls the height to retract to the next layer position (The slow stage) - (Improvement) When converting from a TSMC enabled to a TSMC unable file, the slowest retract speed will be enforced - **Layer:** - (Add) `Number` property to get the layer number, 1 started - (Fix) `HaveGlobalParameters` property was not comparing the `PositionZ` resulting in `true` when different heights are used but keeping all other settings the same - (Fix) `HaveGlobalParameters` property was not comparing the `WaitTimeAfterCure` for bottom layers - (Fix) `MaterialMilliliters` calculation with the real layer height instead of global information and recalculate when height changes (#266) - **CTB:** - (Improvement) Discovered more unknown fields and set them accordingly - (Improvement) When all layers share same settings as globals it will set to follow global table instead of per layer settings - (Fix) VDT: Wrong binding to json 'retract_distance2' key - (Fix) XYZ Accuracy: 'Total height' text showing a F3 and no decimals |
||
|
Tiago Conceição
|
80a9adbcd0 |
v2.18.0
- **Command line arguments:** - (Add) Convert files: UVtools.exe -c \<inputfile\> \<outputfile1/ext1\> [outputfile2/ext2] - (Add) Extract files: UVtools.exe -e \<inputfile\> [output_folder] - https://github.com/sn4k3/UVtools#command-line-arguments - **File formats:** - (Add) Implement TSMC (Two Stage Motor Control) for the supported formats - (Add) Implement 'Bottom retract speed' for the supported formats - (Add) LGS: Support for lgs120 and lg4k (#218) - (Add) CTB: Special/virtual file extensions .v2.ctb, .v3.ctb, .v4.ctb to force a convertion to the set version (2 to 4). The .ctb is Version 3 by default when creating/converting files - (Improvement) Better performance for file formats that decode images in sequential pixels groups - **GCode:** - (Improvement) Better parsing of the movements / lifts - (Improvement) Better handling of lifts performed after cure the layer - (Improvement) More fail-safe checks and sanitize of gcode while parsing - (Improvement) CTBv3: Enable per layer settings if disabled when fast save without reencode - (Upgrade) .NET from 5.0.8 to 5.0.9 - (Fix) PrusaSlicer printer: Longer Orange 4k with correct resolution and display size - (Fix) Odd error when changing properties too fast in multi-thread |
||
|
Tiago Conceição
|
ada646f92d |
v2.16.0
- **(Add) PrusaSlicer printers:** - Creality HALOT-MAX CL-133 - Nova3D Elfin2 - Nova3D Elfin2 Mono SE - Nova3D Elfin3 Mini - Nova3D Bene4 - Nova3D Bene5 - Nova3D Whale - Nova3D Whale2 - **About box:** - (Add) Runtime information - (Fix) Limit panels width and height to not overgrow - **(Fix) macOS:** - macOS version auto-upgrade (Will only work on future releases and if running v2.16.0 or greater) - Demo file not loading - Auto disable windows scaling factor when on Monjave or greater on new instalations - (Add) Tool: Raise platform on print finish - (Add) CXDLP: Support for Halot MAX CL-133 - (Improvement) Tools: Better handling/validation of tools that are unable to run with abstraction - (Improvement) CWS: Simplify filenames inside the archive - (Upgrade) EmguCV from 4.5.2 to 4.5.3 - (Change) Allow to set layer `LightPWM` to 0 - (Fix) Arrange dropdown arrow from layer image save icon to be at center |
||
|
Tiago Conceição
|
2d79c6504f |
v2.15.1
- **(Improvement) CWS:** - Remove light-off delay from the format - Sync movements with a delay time - Auto convert the light-off delay time to wait before cure time when required - **(Improvement) CTB:** - When positively set the 'Wait time before cure' property on a CTBv3 or lower, it will compute the right light-off delay with that extra time into consideration - When positively set any of the light-off delays on a CTBv4 it will auto zero the 'Wait times' properties and vice-versa - Automation to set light-off delay on file load, will no longer do when any of 'Wait times' are defined for a CTBv4 - (Improvement) PrusaSlicer printers that use .cws format, implement the wait times on printer notes - (Fix) GCode parser: Commented commands were being parsed - (Fix) Exposure time information on bottom status bar was inverted, showing normal/bottom time instead of bottom/normal - (Fix) macOS: Installing libusb is no longer a requirement |
||
|
Tiago Conceição
|
a648610d59 |
v2.15.0
- **File formats:** - (Add) Wait time before cure: The time to rest/wait in seconds before cure a new layer - (Add) Wait time before after: The time to rest/wait in seconds after cure a new layer - (Add) Wait time after lift: The time to rest/wait in seconds after a lift/peel move - (Change) All gcode file formats dropped light-off delay field in favor of new 'Wait time before cure' field, setting light-off delay still valid but it redirects to the new field - (Change) Reorder 'Light-off delay' before 'Exposure time' - (Improvement) Recalculate the print time when a related property changes - (Fix) Generic time estimation calculation was ignoring exposure times - (Fix) Unable to load files with uppercase extensions - (Fix) ZIP: Use G1 at end of gcode instead of G0 - (Fix) CWS: Use G1 for movements - **(Fix) CXDLP:** (#240) - Layer area calculation - Validation checksum - **(Fix) ZCODE:** - Use G1 at end of gcode instead of G0 to prevent crash to top bug on firmware - Put back the M18 motors off at end of gcode - **GCode Builder/Parser:** - (Add) Allow to choose between G0 and G1 for layer movements and end gcode - (Fix) Safe guard: If the total print height is larger than set machine Z, do not raise/lower print on completeness - (Fix) Light-off delay is the real delay time and not the calculated movement of the lifts plus the extra time - (Improvement) Parse gcode line by line instead searching on a group of layers to allow a better control and identification - **Tools:** - **Change print parameters:** - (Add) Tooltips to labels - (Add) Sun UTF-8 to the Light PWM value unit to describe intensity - (Improvement) Dynamic lifts: Round lift height and speed to 1 decimal - (Fix) Exposure time finder: Time estimation when using 'Use different settings for layers with same Z positioning' - **Prusa Slicer:** - (Add) Note keyword: BottomWaitBeforeCure_xxx - (Add) Note keyword: WaitBeforeCure_xxx - (Add) Note keyword: BottomWaitAfterCure_xxx - (Add) Note keyword: WaitAfterCure_xxx - (Add) Note keyword: BottomWaitAfterLift_xxx - (Add) Note keyword: WaitAfterLift_xxx - (Change) Uniz IBEE: Remove light-off delay and implement wait time keywords - **macOS:** (#236) - (Remove) osx legacy packages from build and downloads - (Fix) macOS: Simplify the libcvextern.dylib and remove libtesseract dependency - (Fix) macOS: Include libusb-1.0.0.dylib - Note: `brew install libusb` still required - **UI:** - (Fix) Refresh gcode does not update text on UI for ZIP, CWS, ZCODEX files - (Fix) Operations: Import a .uvtop file by drag and drop into the UI would not load the layer range - (Change) When convert a file, the result dialog will have Yes, No and Cancel actions, where No will open the converted file on current window, while Cancel will not perform any action (The old No behaviour) |